1. Choose one matching pair
Choose Orbit Mix or Sunny Mix. Use that design's FRONT and BACK pages. Print at 100% / Actual Size with Fit to Page off. Measure both 50 mm lines; correct the settings if either differs by more than 1 mm.
Printable
Candy Paper Squishy Template: Custom Wrapper & Guide
Make an original candy pouch with matching front and back panels.
- Format
- PDF / SVG
- Paper
- A4 / US Letter
- Print options
- Color or black & white
- Time
- See steps
Get the free PDF Add your own textNo account or email needed. Choose your paper size below.
Choose your free PDF
Choose the paper size that matches your printer. Use Actual Size / 100%, with Fit to Page off.
Look inside the printable PDF
Complete candy bag pack
A4 ColorPDF · 7 pages · 587 KB · v2Download PDF ↓Complete candy bag pack
A4 Black & whitePDF · 7 pages · 555 KB · v2Download PDF ↓Complete candy bag pack
Letter ColorPDF · 7 pages · 587 KB · v2Download PDF ↓Complete candy bag pack
Letter Black & whitePDF · 7 pages · 555 KB · v2Download PDF ↓
A4 ColorPDF · 7 pages · 587 KB · v2Download PDF ↓Complete candy bag pack
A4 Black & whitePDF · 7 pages · 555 KB · v2Download PDF ↓Complete candy bag pack
Letter ColorPDF · 7 pages · 587 KB · v2Download PDF ↓Complete candy bag pack
Letter Black & whitePDF · 7 pages · 555 KB · v2Download PDF ↓
Vector net sheets (SVG) · A4 and Letter
Editable outline companions generated from the same geometry as the PDF. Choose the same paper size and matching front/back pair. The solid outer line is for cutting; the dashed inner line marks a 6 mm sealing band, not a fold. Keep the 20 mm A opening until filling is finished. Print at 100% and measure the 50 mm calibration line; editing or browser print scaling can change dimensions. The complete PDF above includes the assembly guide.
Vector net · Orbit front
A4 · SVG · v23 KB · one sheetDownload SVG ↓Vector net · Orbit back
A4 · SVG · v22 KB · one sheetDownload SVG ↓Vector net · Sunny front
A4 · SVG · v23 KB · one sheetDownload SVG ↓Vector net · Sunny back
A4 · SVG · v22 KB · one sheetDownload SVG ↓Vector net · Orbit front
Letter · SVG · v23 KB · one sheetDownload SVG ↓Vector net · Orbit back
Letter · SVG · v22 KB · one sheetDownload SVG ↓Vector net · Sunny front
Letter · SVG · v23 KB · one sheetDownload SVG ↓Vector net · Sunny back
Letter · SVG · v22 KB · one sheetDownload SVG ↓
A4 · SVG · v23 KB · one sheetDownload SVG ↓Vector net · Orbit back
A4 · SVG · v22 KB · one sheetDownload SVG ↓Vector net · Sunny front
A4 · SVG · v23 KB · one sheetDownload SVG ↓Vector net · Sunny back
A4 · SVG · v22 KB · one sheetDownload SVG ↓Vector net · Orbit front
Letter · SVG · v23 KB · one sheetDownload SVG ↓Vector net · Orbit back
Letter · SVG · v22 KB · one sheetDownload SVG ↓Vector net · Sunny front
Letter · SVG · v23 KB · one sheetDownload SVG ↓Vector net · Sunny back
Letter · SVG · v22 KB · one sheetDownload SVG ↓
No account or email needed. Original downloads are for personal, family and classroom use.
Make it yours.
Choose a palette and expression, then add up to 18 English letters, numbers or basic punctuation. Your text stays in this browser. The default PDFs above are ready to print without customization.
Make it yours
Colors and a short name. The cut lines stay in place.
Exports this wrapper. Both patterns are included in the default pack.
Up to 18 English letters, numbers, spaces or basic punctuation, within the name area. Text stays on this device.Use a default PDF insteadWhat you need
- Matching A4 or US Letter paper, 80-100 gsm (prototype assumption)
- Ruler, scissors and clear tape
- A small amount of clean tissue; keep filling out of the seams
Follow the steps
Read the existing instructions one step at a time. Checks are self-reported on this device; they do not verify a successful build or a tested physical design.
0 of 6 steps checked.
2. Cut two panels
Cut only the solid outside rectangle on each page. Keep A at the top and B at the bottom. The dashed inner rectangle marks the 6 mm sealing band: do not cut or fold it. Use help with scissors where needed.
3. Put blank faces together
Turn the BACK panel so its blank side meets the FRONT panel's blank side. Both prints face out. Match A to A at the top and B to B at the bottom. Slide the front panel over the blank side of the back panel; keep both upright.
4. Tape the perimeter; leave A open
Wrap short strips of clear tape around both paper edges, with about 6 mm on each printed face. Tape the sides, bottom and top shoulders. Leave only the marked 20 mm opening at A. Overlap adjacent strips slightly.
5. Fill through the top opening
Feed small, loose pieces of clean tissue through A. Start with less filling than you expect to need. Keep the sealing band flat and free of filling. The close-up shows the same top opening enlarged, not an extra part.
6. Close the last 20 mm
Bring the two top edges together at A and wrap tape across the last opening. Check both faces and every seam. Press lightly and record any tearing, leaking or flattening. Finished thickness and recovery depend on the actual materials.
If something is not working
The two panels do not match
Check that the part names, version and paper size match. Verify both 50 mm lines, then match A at the top and B at the bottom. Do not trim one panel to hide a mismatch.
The corner or neck will not close
Keep the filling away from the seam and use shorter tape strips. If the 6 mm sealing band cannot be used, stop and record the exact corner for a geometry revision.
The paper tears or stays flattened
Record the paper and filling amount, then photograph the failure. This prototype has no tested recovery behavior.
Before you begin
- Two original geometric wrapper patterns. Both use the same 100 x 130 mm flat outline.
- An untested paper construction prototype. All sizes and sealing bands are design assumptions.
- Not food or a product for mouthing. No slow-rise or recovery performance is claimed.
- Use adult assistance for cutting where needed.